On this page
Leq is the steady level that would carry the same sound energy as the fluctuating noise you measured. It is the main number for exposure and most noise assessments. Lmax is the loudest time-weighted moment and Lpeak the highest instantaneous pressure. The Ln values are statistics: L10 is the level exceeded 10% of the time (the noisy bits), L50 the median, and L90 the level exceeded 90% of the time, which is the usual measure of background noise.
Leq: the equivalent continuous level
Real noise goes up and down. Leq (also written LAeq when A-weighted, or LAeq,T with the measurement time T) answers one question: what constant level would deliver the same total sound energy over the same time?
Because decibels are logarithmic, Leq is an energy average. Each reading is converted back to energy, the energies are averaged, and the result is converted back to dB:
Leq = 10 × log10( (1/N) × Σ 10^(Li/10) )
This has a big practical effect. A few loud moments can dominate the result. One minute at 90 dB contains as much energy as 10 minutes at 80 dB, or 100 minutes at 70 dB. That is also why Leq is the basis of noise exposure: your ears respond to the total energy received, and workplace limits like 85 dBA over 8 hours are Leq values. See noise dose and TWA for how that becomes a daily dose.
Leq doesn’t depend on the meter’s Fast or Slow setting. Those only affect the live display and the maximum, as explained in Fast, Slow and Impulse time weighting.
Lmax and Lpeak: the loudest moments
- Lmax is the highest level the meter showed, using its time weighting. It is usually written
LAFmax(A-weighted, Fast) orLASmax(Slow). It is used for intermittent sounds like trains, aircraft, door slams or shouting, which can disturb sleep even when the Leq is modest. - Lpeak is the highest instantaneous pressure, with no time smoothing. It is usually C- or Z-weighted (
LCpeak). It matters for hearing damage from impacts and explosions, where workplace rules typically set limits around 135 to 140 dB(C).
There is also Lmin, the lowest time-weighted level, but it is sensitive to a single quiet instant, so L90 is a more robust way to describe the quiet end.
L10, L50 and L90: percentile levels
Statistical (percentile) levels describe how the level was distributed. The meter samples the level many times a second and sorts the results. Ln is the level exceeded for n% of the time.
| Level | Exceeded for | What it describes |
|---|---|---|
| L1 or L5 | 1% or 5% of the time | Near the loudest events, less affected by one freak spike than Lmax |
| L10 | 10% of the time | The noisy part: regular events such as passing traffic |
| L50 | 50% of the time | The median, a “typical” level |
| L90 | 90% of the time | Background noise in the gaps between events |
The order is always L10 ≥ L50 ≥ L90. The gap between L10 and L90 tells you how much the noise fluctuates. A steady fan gives almost no gap. A street with occasional cars can have a gap of 15 dB or more.
A worked example
Say you measure a quiet street on an evening for 10 minutes and note the A-weighted Leq for each minute:
| Minute | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
|---|---|---|---|---|---|---|---|---|---|---|
| LAeq, 1 min | 42 | 43 | 43 | 44 | 45 | 46 | 48 | 52 | 58 | 66 |
- Simple average of the numbers: 48.7 dB. This is not a meaningful noise level.
- Leq over 10 minutes: about 57 dBA. The single minute at 66 dB, when a motorbike went past, contains more energy than the other nine minutes combined. Without it, the Leq of the remaining nine minutes would be about 50.5 dBA.
- L90 is near the bottom of the range, around 42 to 43 dBA: the background you hear when nothing is happening.
- L50 is around 45 to 46 dBA.
- L10 is near the top, somewhere around 58 dBA or above.
This is a simplified illustration. A real meter calculates percentiles from many short samples rather than ten one-minute values, so its figures would be more precise. The pattern is what matters: Leq is dragged up by the loud event, L90 isn’t.
You can check energy averages like this with the decibel addition calculator, or read how decibels add up for the maths.
Why background L90 matters for complaints
How annoying a sound is depends heavily on how much it stands out from the background. A fan at 40 dBA can be unnoticeable on a busy road and maddening in a quiet bedroom at night. That is why many assessment methods compare the noise in question with the existing background level, typically the LA90 measured when the source is off.
A well-known example is the British standard BS 4142, used for industrial and commercial sound affecting homes. It compares a “rating level” for the source with the background LA90. Broadly, a source around 10 dB or more above background is likely to indicate a significant adverse impact, and around 5 dB above an adverse impact, depending on context. Other countries and local authorities use their own rules, so check what applies where you live.
If you are documenting a noise problem, record:
- The background (LA90 and LAeq) at a time when the noise is absent, at the same location and time of day.
- The noise (LAeq, LAFmax, and LCeq if there is heavy bass) while it is happening.
- Date, time, duration, location and what you could hear.
The guide to measuring neighbour noise covers this step by step. Phone readings are estimates, but the difference between background and noise, measured on the same device in the same place, is often more reliable than either absolute number. This isn’t legal advice; a formal complaint may need a measurement by an environmental health officer or a consultant with a calibrated meter.
Which number to quote
- Hearing exposure: LAeq over the exposure period, plus LCpeak for impacts.
- Sleep disturbance: LAeq for the night and LAFmax for individual events. See noise levels for sleep.
- Background or ambient quiet: LA90.
- Traffic and general environmental noise: LAeq, often with LA10.
Always state the weighting, the duration and the location with the number. “57 dB” on its own says very little. “LAeq,10min 57 dB at the bedroom window” says a lot.
Frequently asked questions
What is the difference between Leq and average dB?
Leq is an energy average, not a simple average of the decibel numbers. Loud moments carry far more energy than quiet ones, so Leq is pulled towards the loudest parts of a measurement and is usually higher than the arithmetic mean of the readings.
What does L90 mean in noise measurement?
L90 is the level that was exceeded for 90% of the measurement time. It ignores short loud events and describes the steady background noise you hear in the gaps between them.
Is L10 higher than L90?
Yes, or at least equal. L10 is the level exceeded 10% of the time, so it sits near the top of the range. L90 is exceeded 90% of the time, so it sits near the bottom. For perfectly steady noise they are the same.
What is the difference between Lmax and Lpeak?
Lmax is the highest time-weighted level (for example Fast, 125 ms) during the measurement. Lpeak is the highest instantaneous sound pressure, with no smoothing. For a sharp impact, Lpeak can be 10 to 20 dB or more above Lmax.
How long should I measure to get L90?
Long enough to include the normal pattern of quiet gaps and noise events. For a fairly steady environment, 5 to 15 minutes is a common starting point. For noise that comes and goes, such as music or a barking dog, measure over the whole period it happens and at the same time of day as the problem.