How Loud Is This?
Measuring

How to measure noise with your phone

Your phone can give a useful estimate of how loud something is, often within a few decibels once calibrated. The way you hold it, where you stand and how long you measure matter as much as the microphone.

Updated · 4 min read

On this page

To measure noise with your phone, open the online sound meter, allow microphone access, hold the phone at ear height at arm’s length away from walls, and measure for 1 to 5 minutes. Note the Leq (the energy average), not the jumping live number, and write down how far you were from the source. Expect a typical accuracy of a few decibels after calibration, and treat anything above about 100 dB as unreliable.

What you need

  • A phone, tablet or laptop with a working microphone and a modern browser.
  • The online sound meter. Nothing to install.
  • Ideally, a calibration offset for your device. Without one you still get useful comparisons, but the absolute number may be several dB off. See how to calibrate a phone sound meter.

Browsers normally clean up the microphone signal for calls with echo cancellation, noise suppression and automatic gain control. Those features would wreck a sound measurement, so the meter asks the browser to turn them off automatically. Some devices also apply processing at the operating-system level that a web page can’t switch off, which is one reason calibration matters.

Step by step

  1. Open the meter and allow the microphone. Your browser will ask for permission the first time.
  2. Remove anything covering the microphone. Thick cases, fingers and pockets block or muffle it. On most phones the main microphone is on the bottom edge.
  3. Stand where the listener would be. To judge what you hear, measure where your head would be. For a bedroom, that is the pillow. For a workstation, it is your seated head position.
  4. Hold the phone at ear height, at arm’s length. Your body reflects and blocks sound. Keep the phone at least 30 cm from your body if you can, and at least 1 metre from walls, windows and large furniture.
  5. Point the microphone roughly towards the source and keep still. Don’t tap, swipe or shift your grip during the measurement; handling noise reaches the microphone directly.
  6. Measure for 1 to 5 minutes. Steady noise like a fan settles quickly. Noise that varies, like traffic, music or a dishwasher cycle, needs longer. Measure through a full cycle if there is one.
  7. Record the Leq and the maximum. Leq describes the whole period. The maximum shows the loudest moment. The guide Leq, L10 and L90 explained covers what each means.
  8. Write down the context: date, time, location, distance from the source, and what you could hear.

Distance changes everything

A reading without a distance is hard to interpret. Outdoors, the level from a small source drops by about 6 dB each time you double your distance. Indoors the drop is usually smaller, because walls and ceilings reflect sound back. A blender might read 90 dBA at 30 cm and 80 dBA across the kitchen. Both are correct, and they answer different questions.

  • To judge hearing risk, measure where your ears actually are.
  • To compare two appliances, measure both at the same distance, for example 1 metre.
  • To estimate the level somewhere else, use the sound distance calculator.

Things that spoil readings

ProblemEffectFix
Wind or a fan blowing on the phoneLarge false low-frequency readingsShelter the phone; outdoors, avoid measuring in a breeze
Touching or moving the phoneThumps and spikes in the maximumHold still, or rest it on a soft surface pointing at the source
Phone flat on a hard tableReflections and vibration pickupHold it, or prop it on something soft
Your own voice or breathingRaises quiet readingsStay silent; hold the phone away from your face
Phone case over the micMuffled, low readingsRemove the case or check the openings are clear
Very loud sound (about 100 dB+)Distortion; readings level off or dropTreat as “at least this loud”; use a proper meter
Very quiet roomReading stuck at the device’s noise floorTreat as “this quiet or quieter”

How accurate is a phone?

Phone microphones are designed for speech, not measurement. They vary between models and even between units of the same model, and they often lose sensitivity at very low and very high frequencies. Rough expectations:

  • Calibrated, moderate broadband noise (about 50 to 90 dBA): often within about 2 to 3 dB of a proper sound level meter.
  • Uncalibrated: can be 5 dB or more off, high or low.
  • Strong bass (subwoofers, engines, heat pumps): tends to read low.
  • Above about 100 dB: many phones distort or limit, so readings can be far too low.
  • Below about 35 to 40 dBA: the device’s own noise sets a floor.

Comparisons are more reliable than absolute numbers. Measuring “before and after” on the same device, in the same position, cancels most of the microphone’s error. That is useful for checking whether a door seal, a rug or a quieter fan made a difference.

Common measuring jobs

Is it loud enough to damage hearing?

Measure at your ear position for a representative period and note the Leq. Around 85 dBA is where long daily exposure starts to carry real risk, and every 3 dB more halves the safe time. Check your result against safe noise exposure times or the noise exposure calculator.

Neighbour or street noise

Measure inside the affected room, with windows as you would normally have them, at the times the noise happens. Measure the background on a quiet occasion too, so you can show the difference. The guide to measuring neighbour noise has a full routine.

Bedroom or nursery

Put the phone where the sleeper’s head would be, measure for several minutes, and record both the Leq and the maximum. See noise levels for sleep.

Frequently asked questions

How accurate are phone decibel meters?

Once calibrated against a proper meter, a phone is often within about 2 to 3 dB for moderate, broadband noise such as voices, traffic or appliances. Uncalibrated, it can be off by 5 dB or more. Accuracy gets worse for very quiet rooms, deep bass and levels above about 100 dB, where many phone microphones distort or limit.

Can I use a phone reading as evidence in a noise complaint?

It can help show a pattern, especially when you log dates, times and durations. Authorities usually rely on their own measurements with calibrated sound level meters for formal action, so treat your readings as supporting information. This isn’t legal advice.

Should I point the phone microphone at the noise?

Point the bottom of the phone, where the main microphone usually is, roughly towards the source, and keep your fingers and case clear of the microphone openings. Holding it at arm’s length matters more than the exact angle for most everyday sounds.

Why does my phone read 30 to 40 dB in a silent room?

Phone microphones and their electronics have their own noise floor. In a very quiet room the reading reflects the device more than the room. Phones are best for levels from roughly 40 to 95 dBA.