On this page
To add decibels, convert each level to energy, add the energies, then convert back. The formula is Ltotal = 10 × log10(Σ 10^(L/10)). In practice, two equal levels add 3 dB (80 dB + 80 dB = 83 dB), and if one level is 10 dB or more below the other it barely changes the total. You can do it in your head with the table below, or use the decibel addition calculator.
Why you can’t just add the numbers
A decibel value is a logarithm of sound energy, as explained in what is a decibel. Each 10 dB step is ten times more energy. Sound energy from independent sources does add normally, so the job is to step out of the logarithm, add, and step back in. When the sources are unrelated (two machines, a fan plus traffic, a voice plus music), this energy sum is the right method.
The formula
For levels L1, L2, L3 and so on:
Ltotal = 10 × log10( 10^(L1/10) + 10^(L2/10) + 10^(L3/10) + … )
Worked example: three machines at 80, 85 and 75 dBA.
- Convert: 10^8.0 = 100,000,000; 10^8.5 ≈ 316,000,000; 10^7.5 ≈ 31,600,000.
- Add: about 448,000,000.
- Convert back: 10 × log10(448,000,000) ≈ 86.5 dBA.
The loudest machine alone is 85 dBA. The other two together add only 1.5 dB.
Quick table for adding two levels
Find the difference between the two levels, then add the amount shown to the higher one.
| Difference between levels | Add to the higher level | Example |
|---|---|---|
| 0 dB | +3.0 dB | 70 + 70 = 73 dB |
| 1 dB | +2.5 dB | 70 + 69 = 72.5 dB |
| 2 dB | +2.1 dB | 70 + 68 = 72.1 dB |
| 3 dB | +1.8 dB | 70 + 67 = 71.8 dB |
| 4 dB | +1.5 dB | 70 + 66 = 71.5 dB |
| 6 dB | +1.0 dB | 70 + 64 = 71 dB |
| 10 dB | +0.4 dB | 70 + 60 = 70.4 dB |
For more than two sources, add them in pairs. Start with the two quietest, then add the result to the next one, and so on. Rounding to the nearest decibel at the end is usually fine.
Many equal sources
For N identical sources, add 10 × log10(N) to the level of one:
- 2 sources: +3 dB
- 4 sources: +6 dB
- 10 sources: +10 dB
- 100 sources: +20 dB
So one person talking at 60 dB becomes about 70 dB with ten people talking at the same level. To most listeners that sounds roughly twice as loud, not ten times.
Subtracting background noise
Often you want the level of one source on its own, but you can only measure it with background noise present. If you measure the total with the source on, then the background with it off, you can subtract:
Lsource = 10 × log10( 10^(Ltotal/10) − 10^(Lbackground/10) )
Example: with the fan on the room reads 65 dB, with the fan off it reads 60 dB. The fan alone is 10 × log10(10^6.5 − 10^6.0) ≈ 63.3 dB.
| Total minus background | Subtract from total | Reliability |
|---|---|---|
| Less than 3 dB | — | Too close to call; the source can’t be separated reliably |
| 3 dB | −3.0 dB | Rough estimate only |
| 4 dB | −2.2 dB | Rough |
| 5 dB | −1.7 dB | Reasonable |
| 6 dB | −1.3 dB | Reasonable |
| 7 dB | −1.0 dB | Good |
| 8 dB | −0.8 dB | Good |
| 10 dB or more | −0.5 dB or less | Background can usually be ignored |
This only works when the background is steady. If it changes between your two measurements, the subtraction can give misleading results, especially when the levels are close. For complaint measurements, the background is usually described with the L90; see Leq, L10 and L90 explained.
Averaging decibel readings
Averaging works the same way: convert to energy, take the mean, convert back.
Laverage = 10 × log10( (1/N) × Σ 10^(L/10) )
Example: one reading of 60 dB and one of 70 dB. The arithmetic mean is 65 dB, but the energy average is about 67.4 dB, because the 70 dB reading carries ten times the energy. This energy average over time is exactly what a meter’s Leq is.
A plain average is only a reasonable shortcut when all the readings are within 2 to 3 dB of each other. For anything more spread out, use the energy average. If you are averaging readings taken at different positions in a room, the same method applies.
Common mistakes
- Adding the numbers directly. 80 + 80 is 83 dB, not 160 dB.
- Mixing weightings. Don’t add a dBA level to a dBC level. Combine like with like. See dBA vs dBC vs dBZ.
- Ignoring distance. Levels only combine directly when they are measured at the same point. A machine that is 90 dB at 1 metre is not 90 dB where you are standing 4 metres away. The sound distance calculator handles that part.
- Assuming quiet sources don’t matter in large numbers. One 70 dB machine next to an 80 dB one adds little, but ten 70 dB machines together make 80 dB on their own, enough to raise the total to 83 dB.
What about two identical sounds in phase?
The energy rule assumes the sounds are unrelated. Two loudspeakers playing exactly the same signal, close together, can combine differently at a given point: up to +6 dB where the waves line up, and much less where they cancel. Across a room and a range of frequencies this tends to average out towards +3 dB, so the energy rule is still the best general method for everyday measurements.
Frequently asked questions
What is 80 dB plus 80 dB?
About 83 dB. Two equal sound sources double the sound energy, and doubling the energy adds 3 dB. It does not make 160 dB.
How many decibels do two equal sources add?
3 dB. Four equal sources add 6 dB, ten add 10 dB and a hundred add 20 dB. The general rule for N equal sources is +10 × log10(N).
Does adding a quieter sound make any difference?
Only a little once it is well below the louder one. A sound 10 dB quieter adds about 0.4 dB, and one 20 dB quieter adds less than 0.1 dB, which no meter or ear will notice.
How do I average decibel readings?
Use an energy average: convert each reading with 10^(L/10), take the mean, then convert back with 10 × log10. The average of 60 dB and 70 dB is about 67.4 dB, not 65 dB. A simple arithmetic average is only close when readings are within a few decibels of each other.