On this page
dBA, dBC and dBZ are the same sound measured through different filters. A-weighting cuts low and very high frequencies the way your ears do at moderate volume, so it is the standard for noise exposure, hearing safety and environmental noise. C-weighting is nearly flat and only trims the extreme ends, so it is used for peak levels and bass-heavy sound. Z-weighting applies no filter at all. If a report just says “dB” with no letter, ask which weighting was used, because the answer can differ by 10 dB or more.
Why meters weight frequencies
Your ear is not equally sensitive to every pitch. At moderate levels it hears best between roughly 1 and 5 kHz, the range of speech consonants, and it is much less sensitive to deep bass. A 50 Hz hum and a 2 kHz tone with the same physical sound pressure do not sound equally loud. They also don’t carry the same risk to your hearing.
A microphone, on the other hand, picks up everything. A frequency weighting is a filter the meter applies before it calculates the level, so the final number lines up better with what a person would hear, or with what a standard asks for. The weightings are defined in the international standard for sound level meters, IEC 61672.
A-weighting (dBA)
A-weighting is based on how the ear responds to fairly quiet sounds. It strongly reduces bass, leaves the mid-range alone and slightly lifts the 2 to 4 kHz region. These are the approximate corrections it applies:
| Frequency | A-weighting | Typical sound at that pitch |
|---|---|---|
| 31.5 Hz | −39.4 dB | Deep sub-bass, distant thunder |
| 63 Hz | −26.2 dB | Kick drum, mains hum harmonics, engine rumble |
| 125 Hz | −16.1 dB | Bass guitar, traffic rumble |
| 250 Hz | −8.6 dB | Lower voice, fans |
| 500 Hz | −3.2 dB | Vowel sounds |
| 1 kHz | 0 dB | Reference frequency |
| 2 kHz | +1.2 dB | Speech clarity, alarms |
| 4 kHz | +1.0 dB | Consonants, squeals |
| 8 kHz | −1.1 dB | Hiss, cymbals |
So a pure 63 Hz tone at 80 dB unweighted reads only about 54 dBA. That is roughly right for how loud it seems at that level, which is the point.
When to use dBA
- Workplace noise and daily exposure (OSHA, NIOSH and EU limits are in dBA)
- Safe listening times, including the exposure time tables
- Traffic, neighbour and environmental noise
- Comparing everyday sounds, as on the decibel chart
C-weighting (dBC)
C-weighting is close to flat across most of the audible range. It only rolls off at the extremes: about −3 dB at 31.5 Hz and at 8 kHz, and less than 1 dB of change from about 63 Hz to 4 kHz. It was designed to match hearing at high levels, where the ear’s response is flatter and bass is heard more fully.
When to use dBC
- Peak levels. Short impulses like hammer blows, nail guns and gunshots are usually limited by their C-weighted peak. EU Directive 2003/10/EC, for example, sets its peak action values at 135 and 137 dB(C) and its peak limit at 140 dB(C).
- Loud music and live sound. Concert and club noise is often monitored in both dBA and dBC, because a bass-heavy mix can read moderately in dBA while still being very powerful. See concert and club noise.
- Hearing protector selection. Some methods for rating hearing protection use the difference between C- and A-weighted levels.
- Low-frequency complaints. Bass from a neighbour’s stereo, a heat pump or a generator can be badly underrated by dBA.
Z-weighting (dBZ)
Z stands for zero. The meter applies no frequency correction between 10 Hz and 20 kHz. It replaced the older, loosely defined “linear” or “flat” settings, which varied between manufacturers. Z-weighting is useful when you want the raw physical level: acoustic engineering, analysing a sound by frequency band, or measuring peaks where a standard asks for an unweighted value.
For everyday use dBZ is rarely the right choice. It gives full weight to infrasound and wind rumble you can’t hear, so it can read high for reasons that have nothing to do with loudness.
B-weighting (and D)
B-weighting sits between A and C. It was meant for medium-level sounds, but it never became widely used and it is not part of the current IEC 61672 standard. You will mostly see it in older textbooks and on vintage meters. D-weighting was developed for aircraft noise and is now also mostly historical. If you read a level in dBB or dBD, treat it as a specialist or legacy figure.
Using the dBC minus dBA gap
Measure the same sound in both weightings and compare them. The difference tells you how much bass is in it:
| dBC − dBA | What it suggests | Examples |
|---|---|---|
| 0–3 dB | Little low-frequency content | Speech, hiss, birdsong, a kettle |
| 4–10 dB | Some bass | General traffic, a busy office |
| More than 10 dB | Strong low-frequency content | Subwoofers, engines idling, compressors, ventilation hum |
These bands are a rule of thumb, not a standard. A large gap is a good reason to describe a noise in dBC as well as dBA, especially in a complaint about neighbour noise, where the thumping bass is often the real problem.
Weighting is not the same as time weighting
Readings like “LAF” or “LCpeak” combine two settings. The first letter after L is the frequency weighting (A, C or Z). The next one is the time weighting: Fast, Slow or Impulse, which controls how quickly the display reacts. So LAFmax is the highest A-weighted, Fast-response level, and LCpeak is the C-weighted true peak. The guide Fast, Slow and Impulse time weighting covers the second half.
Which weighting should you pick?
- Is this loud enough to harm my hearing over time? dBA, averaged over time (Leq).
- Did that one bang exceed a safe peak? dBC peak.
- Why does this bass annoy me when the dBA reading looks fine? Measure dBA and dBC and compare.
- What is the actual physical sound pressure? dBZ.
For most everyday questions, dBA is the reading you want, and it is what you should look at on the online sound meter. Keep in mind that phone and laptop microphones often lose sensitivity at very low frequencies, so they tend to under-read deep bass in any weighting.
Frequently asked questions
Is dBA or dBC louder?
For the same sound, dBC is almost always the same or higher than dBA, because C-weighting removes far less of the bass. The gap is small for speech or a hiss and large for bass-heavy sounds like subwoofers, engines and ventilation rumble.
Which weighting should I use for hearing safety?
Use dBA for average levels and exposure time. Workplace limits from OSHA, NIOSH and EU Directive 2003/10/EC are all set in dBA. For short, sharp peaks such as hammer blows or gunshots, limits are usually given as a C-weighted peak (dBC peak).
What does it mean if dBC is much higher than dBA?
A large difference means the sound has a lot of low-frequency energy. If dBC is more than about 10 to 15 dB above dBA, the A-weighted number probably understates how intrusive the sound is, and a closer look at the bass content is worthwhile.
Is dBZ the same as dB SPL?
Practically, yes. dBZ means zero weighting: the meter treats frequencies across the audible range (10 Hz to 20 kHz in the IEC 61672 definition) equally. Older meters called this “linear” or “flat”.