On this page
Time weighting is how much a sound level meter smooths its reading. Fast (F) averages with a 125 millisecond time constant and follows speech, music and traffic closely. Slow (S) uses a 1 second time constant and gives a steadier number that is easier to read by eye. Impulse (I) rises in 35 ms and decays slowly, and is now mostly a legacy setting. For a single number that describes a whole measurement, use Leq, which doesn’t depend on time weighting at all.
What time weighting actually does
Sound pressure changes thousands of times a second. A display that showed every instant would be unreadable. Meters therefore square the signal and pass it through an averaging filter with a set time constant, then convert the result to decibels. A short time constant reacts quickly. A long one reacts slowly and irons out the bumps.
The time constant is roughly how long the meter takes to catch up with a sudden change. With Fast, a steady tone that switches on is read close to its true level within a few tenths of a second. With Slow, it takes a few seconds. Sounds shorter than the time constant are under-read, because the meter never fully catches up before they stop.
The three settings compared
| Setting | Time constant | Behaviour | Typical use |
|---|---|---|---|
| Fast (F) | 125 ms | Follows rapid changes; display moves a lot | Most modern measurements, maximum levels (LAFmax), music, speech, traffic |
| Slow (S) | 1 s | Smooths fluctuations; steady display | Reading a fluctuating level by eye; regulations that specify slow response |
| Impulse (I) | 35 ms rise, about 1.5 s decay | Jumps up quickly and holds the reading | Older impulsive-noise methods; not recommended for hearing-risk assessment |
Time weighting is written as the third letter in level names: LAF is A-weighted Fast, LAS is A-weighted Slow, LAI is A-weighted Impulse. The second letter is the frequency weighting, explained in dBA vs dBC vs dBZ.
Fast: the default for most jobs
Fast was chosen because 125 ms is roughly how long the ear takes to judge the loudness of a sound. It tracks syllables of speech, drum hits and passing cars well enough to give a realistic maximum. Many standards and guidelines that ask for a maximum level specify LAFmax, the highest A-weighted Fast reading during the measurement.
The downside is that the number moves constantly. If you are trying to read a value off a screen, Fast can make it hard to say what the level “is”. That is a display problem, not a measurement problem: look at Leq or the maximum instead of the live figure.
Slow: steady readings
Slow averages over about a second, so the reading drifts rather than jumps. It is helpful for fairly steady noise with small fluctuations, such as a fan, a road in the distance or machinery running continuously. Some regulations specify it. The US OSHA occupational noise standard, for example, describes measurements on the A scale at slow response.
Slow gives lower maximum levels than Fast for anything short. A single shout that reads 85 dBA on Fast might read only around 80 dBA on Slow, because the shout ends before the meter catches up. The exact difference depends on the sound. If you report a maximum, always say which time weighting you used.
Impulse: mostly historical
Impulse was designed to show how loud a short burst seemed by rising very fast (35 ms) and then falling slowly (about 1.5 s) so you could read it. In practice it doesn’t match how the ear is damaged by impulses, and the current sound level meter standard, IEC 61672, does not require meters to have it and notes it is not suitable for assessing hearing risk. You will still find it on many meters and in some older local rules for things like door slams or shooting ranges.
Peak level is different
For hammer blows, nail guns, gunshots and fireworks, what matters for hearing is the true peak: the highest instantaneous pressure. Lpeak (often LCpeak, C-weighted) has no time weighting. It is typically far higher than any Fast, Slow or Impulse reading of the same event, because those all smooth away the very top of a sharp spike. Peak limits are usually around 135 to 140 dB(C) in workplace rules.
Why Leq makes time weighting less important
The equivalent continuous level, Leq, adds up the sound energy over the whole measurement and expresses it as one steady level. Because it integrates energy directly, it gives the same answer whether the meter is set to Fast, Slow or Impulse. For noise exposure, neighbour noise and room comparisons, Leq is usually the number you want, with Lmax alongside it to show the loudest moments. The guide Leq, L10 and L90 explained goes through these.
Which setting to use
- General measurements: Fast, and record Leq.
- Maximum level of passing traffic, music or voices: Fast (LAFmax).
- Reading a steady machine or room level by eye: Slow.
- Following a specific regulation: whatever it specifies. Check the text rather than guessing.
- Short bangs and impacts: peak level, preferably on a proper sound level meter.
When you measure with the online sound meter, treat the live figure as a guide and note down the Leq. For a full routine, see how to measure noise with your phone.
Frequently asked questions
Should I use Fast or Slow on a sound meter?
Use Fast for most measurements and for maximum levels, and when a standard asks for it. Use Slow when the sound fluctuates and you want a steadier display to read by eye, or when a rule such as OSHA’s workplace noise standard specifies slow response. For anything you will report, record Leq as well, since it does not depend on time weighting.
Does time weighting affect Leq?
No. Leq is an energy average over the whole measurement, so Fast, Slow and Impulse all give the same Leq for the same sound. Time weighting affects the moment-to-moment reading and the maximum and minimum levels.
Is Impulse the same as peak?
No. Impulse still smooths the signal, with a 35 ms rise, so it reads well below the true peak of a very short sound like a gunshot. Peak level (Lpeak) has no time weighting at all and captures the highest instantaneous pressure.
Why does my reading jump around so much?
You are probably on Fast, which follows changes within about an eighth of a second. That is normal for speech, music and traffic. Switch to Slow for a calmer display, or look at Leq for a single representative number.