How Loud Is This?
Health

Hearing protection ratings (NRR and SNR) explained

The NRR on a box of earplugs is a lab number. In real use you usually get much less. A common workplace estimate is (NRR − 7) ÷ 2 decibels of protection in dBA, so an NRR 33 foam plug is counted as about 13 dB.

Updated · 4 min read

On this page

The Noise Reduction Rating (NRR) is the number of decibels a hearing protector blocked in a standard lab test, under ideal fitting. Real-world protection is usually lower. To estimate it, subtract 7 from the NRR if you are working with dBA levels, then divide by 2 to allow for imperfect fit. Example: at 100 dBA, an NRR 29 earplug is counted as (29 − 7) ÷ 2 = 11 dB, leaving about 89 dBA at your ear.

What NRR means

In the US, the EPA requires hearing protectors to carry an NRR label. It comes from lab tests where trained subjects fit the protector carefully, and the attenuation is measured across a range of frequencies. The result is designed to be subtracted from a C-weighted noise level (dBC).

Two problems come up in practice:

  • Most readings are in dBA. Sound meters and noise limits usually use A-weighting. Because a dBA reading already discounts low frequencies, NRR and dBA don’t line up directly. The standard correction is to subtract 7 dB from the NRR before using it with dBA. See dBA vs dBC for why the weightings differ.
  • Real fit is worse than lab fit. Studies of workers in the field consistently find less attenuation than the label, often much less. That is why the label number gets derated.

How to derate NRR for real-world use

The OSHA method

OSHA’s guidance for estimating whether protection is adequate uses a 50% safety factor: protection (dBA) ≈ (NRR − 7) ÷ 2.

The NIOSH method

NIOSH suggests derating by device type, because some types lose more protection in real use than others:

Device typeNIOSH derating
EarmuffsUse 75% of the NRR
Formable (foam) earplugsUse 50% of the NRR
All other earplugsUse 30% of the NRR

The derated value applies to dBC levels; for dBA, subtract a further 7 dB.

Worked example at 100 dBA

ProtectorLabel NRROSHA estimateNIOSH estimate
Foam earplugs3313 dB → about 87 dBA16.5 − 7 ≈ 10 dB → about 90 dBA
Earmuffs259 dB → about 91 dBA18.75 − 7 ≈ 12 dB → about 88 dBA

These are deliberately cautious planning figures. Someone who inserts foam plugs well can get far more than 13 dB. But because you can’t see how well a plug is fitted, the cautious figure is the safe one to plan with.

SNR and other ratings outside the US

In Europe, protectors are tested to the EN 352 series and labelled with an SNR (single number rating), plus H, M and L values for high, medium and low frequency noise. SNR is designed to be subtracted from the dB(C) level. The calculation differs from NRR, so the same product usually shows a higher SNR than NRR; don’t compare the two numbers directly.

The same real-world gap applies. UK HSE guidance, for example, recommends reducing the calculated protection by 4 dB to allow for real-world factors. Other countries use their own ratings, such as SLC80 in Australia and New Zealand.

Foam plugs vs earmuffs vs musician earplugs

TypeStrengthsWeaknesses
Foam earplugsHighest labelled ratings, cheap, lightProtection depends heavily on insertion. Muffles speech and music unevenly
Pre-moulded (flanged) plugsReusable, quick to insert, washableNeed the right size. Lower real-world protection on average
EarmuffsEasy to fit consistently, easy to check from a distanceHot, bulky. Glasses frames, hair and hats break the seal
Musician or “high-fidelity” plugsReduce level fairly evenly across frequencies, so music and speech stay clearLower attenuation, often about 9 to 25 dB. Not enough for very loud industrial noise
Custom-moulded plugsComfortable for long wear, repeatable fitCost, and they still need checking as ears change

For concerts, clubs and rehearsals, flat-response musician plugs are often the best choice because people actually keep them in. For more on that, see concert and club noise. For chainsaws, gunfire or heavy machinery, use high-rated plugs, muffs or both.

Doubling up: plugs and muffs together

Wearing earplugs under earmuffs does not add the two ratings. Sound reaches the inner ear through the bones of the skull as well as through the ear canal, and that path limits the total. A common rule of thumb, used in OSHA guidance, is to take the estimate for the higher-rated protector and add 5 dB:

(33 − 7) ÷ 2 + 5 = 18 dB, so 105 dBA becomes about 87 dBA.

Doubling up is usually advised when levels are above about 100 to 105 dBA.

Fit matters more than the label

The biggest difference between good and poor protection is how the protector is worn.

  • Foam plugs: roll the plug into a thin, tight cylinder. Reach over your head and pull the top of your ear up and back to straighten the canal. Insert the plug well in, then hold it for 20 to 30 seconds while it expands. Very little should stick out.
  • Check the seal: with plugs in, cup your hands over your ears. If the noise gets much quieter, the plugs aren’t sealing well.
  • Earmuffs: the cushions must seal all round. Glasses arms, hair and hoods leak noise. Replace hardened or cracked cushions.
  • Wear time: removing protection for even a short part of a loud shift wipes out much of the benefit, because the unprotected minutes dominate the dose.
  • Don’t overprotect: aiming for about 70 to 80 dBA at the ear usually keeps you safe while you can still hear speech and alarms.

Some employers and hearing clinics offer fit testing, which measures the protection you actually get from a specific protector. It is the best way to know. To estimate the noise you are protecting against, measure it with the online sound meter, keeping in mind that phone readings are estimates and less accurate above about 100 dB.

Frequently asked questions

How much does NRR 33 actually reduce noise?

In a lab, with perfect fit, close to the label. In real use, a common OSHA estimate is (33 − 7) ÷ 2 = 13 dB in dBA. A well-fitted foam plug can do much better than that; a badly inserted one can do worse.

Do you subtract the NRR from the decibel level?

Not directly. The NRR is meant to be subtracted from a C-weighted level. If you know only the dBA level, subtract 7 from the NRR first. Then derate for real-world fit, for example by halving it.

Does wearing earplugs and earmuffs together double the protection?

No. A common rule of thumb is that doubling up adds only about 5 dB to the better of the two protectors. It is still worth doing in very loud noise, above about 100 to 105 dBA.

What is the difference between NRR and SNR?

Both are single-number ratings from lab tests. NRR is used in the US under EPA labelling rules. SNR (single number rating) is used in Europe under EN 352 and is calculated differently, so the same protector usually has a higher SNR than NRR. They can’t be compared directly.

Is there such a thing as too much hearing protection?

Yes. If protection is so strong that you can’t hear speech or warning signals, people tend to remove it. For most noise, aiming for about 70 to 80 dBA at the ear is enough.