On this page
Keep a baby’s white noise machine at around 50 dBA or lower at the crib, place it at least 2 metres (about 7 feet) away from where the baby sleeps, never inside or on the crib, and use the lowest volume that works. A 2014 study published in Pediatrics, the journal of the American Academy of Pediatrics, found that infant sleep machines can easily exceed that level when placed close and turned up.
What the research found
In 2014, researchers in Toronto tested 14 infant sleep machines and published the results in Pediatrics. They played each machine at maximum volume and measured the sound at distances matching a machine placed on the crib rail, beside the crib, and across the room.
- At 30 cm (roughly crib-rail distance), every machine tested exceeded 50 dBA at maximum volume.
- A few machines were loud enough at 30 cm to exceed 85 dBA, the level used in workplace hearing rules for an 8-hour shift.
- Levels fell with distance, so moving the machine away made a real difference.
The researchers compared their results with the 50 dBA limit recommended for hospital nurseries. Their advice to parents was to place machines as far from the infant as possible, keep the volume low, and limit how long the machine runs.
The study measured the machines’ output, not babies’ hearing, so it doesn’t show that any particular machine has harmed a child. But babies can’t move away or turn a machine down, and their ear canals are small, so a cautious approach makes sense.
Safe setup at a glance
| Setting | Recommendation |
|---|---|
| Level at the crib | About 50 dBA or lower, measured where the baby’s head lies |
| Distance | At least 2 m (7 ft) from the crib |
| Position | Never in the crib, on the rail or attached to the cot; out of reach |
| Volume | The lowest setting that helps, well below maximum |
| Duration | Use a timer if possible, rather than running all night at a high level |
How to check your machine with the sound meter
- Set up as at bedtime. Machine in its usual place, at your usual volume, door and windows as normal.
- Put your phone where the baby’s head lies, face up on the mattress, with the baby out of the crib. Don’t hold it; your hand and body change the reading.
- Open the online sound meter, make sure it is reading in dBA, and keep the room otherwise quiet.
- Watch it for 30 to 60 seconds and note the average level. White noise is steady, so the reading should settle.
- Adjust. If it’s above about 50 dBA, turn the machine down or move it further away, then measure again.
- Switch the machine off and measure the room as well. That gives you the background level the machine is masking.
How loud is 50 dBA?
50 dBA is roughly the level of a quiet conversation a few metres away, a quiet office or a refrigerator hum heard close up. It is noticeably quieter than normal conversation at about 60 dBA. If you have to raise your voice to talk next to the crib, the machine is too loud. For more comparisons, see the decibel chart.
Remember that 10 dB more is about ten times the sound energy. A machine reading 60 dBA at the crib is putting out ten times the energy of one at 50 dBA, even though it sounds only about twice as loud. The guide what is a decibel? explains why.
Distance does a lot of the work
Sound from a small source spreads out as it travels. In open space, each doubling of distance cuts the level by about 6 dB. In a bedroom, walls reflect some sound back, so the drop is usually smaller, but distance still helps. Moving a machine from the crib rail to the far side of the room can lower the level at the baby by 10 dB or more. The sound distance calculator gives an idea of the free-field effect.
Point the speaker away from the crib, toward a wall or the door, if your machine is directional.
Accuracy of phone readings
At around 50 dBA, a calibrated phone is typically within a few decibels of a proper sound level meter, which is accurate enough for this check. Uncalibrated phones can be off by more, and readings vary between models. If your reading is close to 50 dBA, err on the side of turning it down a little. For better accuracy, see how to calibrate a phone sound meter.
Other tips
- Choose steady sound. Plain white, pink or brown noise without sudden changes, music or voices.
- Measure every new machine. Volume steps vary between models, so “setting 3” on one isn’t the same as on another.
- Re-check when you move the crib or the machine.
- Mind the batteries. Some machines change volume as batteries run down; plug-in models are more consistent.
- Talk to your paediatrician if your baby seems not to react to sounds, or if you have any worries about hearing.
For adults, see noise levels for sleep for the WHO bedroom guidelines.
Frequently asked questions
How many decibels should white noise be for a baby?
Aim for around 50 dBA or lower where your baby’s head is. That matches the 50 dBA level that researchers used as a reference, which is the level recommended for hospital nurseries. Use the quietest setting that still helps.
How far should a white noise machine be from a crib?
At least about 2 metres (7 feet), and never inside or attached to the crib. The authors of a 2014 study in Pediatrics recommended placing machines as far from the infant as practical.
Is it safe to run white noise all night for a baby?
The researchers suggested limiting how long machines run, for example using a timer that switches off after the baby falls asleep. If you do run it longer, keeping the level low and the machine far away matters even more. Ask your paediatrician if you’re unsure.
Can I check the volume with my phone?
Yes, as an estimate. Put the phone where the baby’s head lies, turn the machine on at your usual setting and read the level in dBA. Phones are typically within a few decibels at this level once calibrated, which is accurate enough to tell 50 dBA from 70 dBA.